8m Stepped Ringlock LED Support Framework with 6m Front and 4m Rear Sections
An 8m-wide, 4m-deep modular Ringlock LED support framework with a 6m-high front section and a 4m-high rear section. Its stepped double-row arrangement combines vertical standards, horizontal members, diagonal bracing, adjustable bases, four LED pallets and five pallet bracket supports to form an independent temporary LED installation structure.
The following BOQ is based on the original DragonTruss product configuration.
Component
Specification
Quantity
Horizontal Pipe
L = 2m
79 pcs
Diagonal Pipe LR3
L = 2.44m
57 pcs
Pillar / Vertical Standard LR1
L = 2m
40 pcs
Adjustable Base LR4
H = 0.25m
15 pcs
Pallet for LED
Source-listed LED pallet
4 pcs
Pallet Bracket Support
Source-listed support bracket
5 pcs
Packing Weight: Approximately 1,300kg
Packing Volume: Approximately 3CBM
The published quantities describe this specific modular arrangement.
They should not be converted into structural load ratings or used to reconstruct unconfirmed connection details.
6. Vertical Standards — 40 Pieces
The BOQ includes:
40 × LR1 Vertical Standards, L = 2m
These form the main upright elements of the structure.
The modular 2m length allows the required front and rear heights to be assembled from repeated standard components.
For example, the 6m front height corresponds geometrically to three 2m vertical modules.
The 4m rear height corresponds geometrically to two 2m vertical modules.
This explains the modular height relationship.
However, the total number of standards does not independently establish the exact number or position of every vertical support line.
The final placement should follow the confirmed assembly drawing.
7. Horizontal Members — 79 Pieces
The BOQ includes:
79 × Horizontal Pipes, L = 2m
These members connect the vertical standards and create the horizontal modular framework.
They are used across the overall 8m width and within the front-to-rear support arrangement.
Their repeated 2m length is consistent with the modular geometry of the structure.
The horizontal members form part of the complete framework, but their exact distribution must follow the source drawing.
8. Diagonal Bracing — 57 Pieces
The BOQ includes:
57 × LR3 Diagonal Pipes, L = 2.44m
The reference structure uses diagonal bracing across the front, side and rear zones.
These diagonal members distinguish the system from a simple arrangement of vertical posts and horizontal pipes.
The rear structural depth provides space for a more extensive bracing layout.
The diagonal arrangement is an important part of the physical configuration, but no verified wind rating, lateral capacity or overall allowable load can be inferred from the brace count alone.
9. Adjustable Bases — 15 Pieces
The BOQ includes:
15 × LR4 Adjustable Bases, H = 0.25m
These provide adjustable lower support positions for the modular Ringlock framework.
The bases are part of the supplied configuration.
They do not automatically establish:
required foundation type;
ground-bearing capacity;
anchoring method;
ballast quantity;
permissible ground slope;
allowable wind conditions.
These matters depend on the actual installation site and final structural design.
10. LED Pallets and Bracket Supports
The source includes two accessory groups that are particularly relevant to the LED installation.
LED Pallets
4 pieces
Pallet Bracket Supports
5 pieces
These components form part of the lower LED-support arrangement.
They should remain visible in the BOQ because they are not ordinary Ringlock standards, ledgers or diagonal braces.
They represent a dedicated interface between the modular framework and the LED installation configuration.
However, the source does not provide separate load calculations or detailed operating specifications for these accessories.
Therefore, the LED pallets should not automatically be described as certified maintenance platforms or assigned an unsupported equipment capacity.
11. How the LED Support Modules Work Together
The complete structure can be divided into four functional modules.
Module A — Tall Front Framework
The 6m-high front section forms the main LED installation face.
Module B — Lower Rear Framework
The 4m-high rear section creates the additional structural depth behind the front.
Module C — Modular Bracing and Base System
Horizontal members, diagonal braces and adjustable bases complete the Ringlock assembly.
Module D — LED Support Accessories
Four LED pallets and five pallet bracket supports form the source-listed LED installation accessory group.
Together, these modules create an independent temporary LED-support framework.
The key structural relationship is not a roof or performance stage.
It is the combination of front height, rear depth, stepped geometry and LED-support accessories.
12. Why This Is Not an LED Hanging Tower
Some temporary LED structures use a different approach.
For example, two independent towers may support an overhead aluminum beam from which an LED display is suspended.
This product does not have that confirmed configuration.
Its BOQ does not include:
an aluminum overhead hanging beam;
a motor hoist;
a dedicated cantilever hanging beam;
a separate pair of LED hanging towers.
Instead, the confirmed components form a continuous modular Ringlock framework with front and rear support sections.
It should therefore be classified as a stepped LED support framework, not an overhead LED hanging system.
13. Difference from the 8x1x6m Ringlock LED Support Wall
A related DragonTruss product uses an 8m-wide, 1m-deep, 6m-high Ringlock LED support wall.
Both products serve temporary LED installation requirements, but their structural arrangements are different.
Feature
8×1×6m LED Wall
This 8×4m Stepped Structure
Width
8m
8m
Overall Depth
1m
4m
Front Height
6m
6m
Rear Height
No separate 4m rear section specified
4m
Structural Arrangement
Shallow modular wall
Stepped double-row framework
Horizontal Members
52 pcs across 1m and 2m lengths
79 pcs, 2m
Diagonal Members
39 pcs across two lengths
57 pcs, 2.44m
Vertical Standards
30 pcs
40 pcs
Adjustable Bases
10 pcs
15 pcs
LED Pallets
4 pcs
4 pcs
Pallet Bracket Supports
5 pcs
5 pcs
Packing Weight
Approx. 835kg
Approx. 1,300kg
Packing Volume
Approx. 2CBM
Approx. 3CBM
The difference is not merely the overall footprint.
The 8×4m structure introduces a separate 4m-high rear section and a much deeper support framework.
The 8×1×6m version is a comparatively shallow LED wall configuration.
Both deserve separate structural descriptions because their layouts answer different installation requirements.
14. Difference from a Complete Concert Stage
This product is a dedicated LED support structure.
It does not include a confirmed:
performance stage;
aluminum stage deck system;
stage stairs;
concert roof;
roof canopy;
line-array support;
lighting rig.
This makes it suitable for consideration as an independent LED-support module within a larger event project.
For example, an event may contain a separate performance stage, roof structure and sound system.
The LED framework can be treated as its own structural module rather than automatically forming part of the main stage roof.
The actual placement and any interfaces with surrounding structures must be confirmed for the project.
15. Practical Assembly Logic
At Product level, the modular arrangement can be understood through the following general sequence.
Establish the 8m-wide × 4m-deep footprint.
Position the 15 adjustable bases according to the confirmed drawing.
Assemble the 2m vertical standards to form the required front and rear support levels.
Install the horizontal pipes across the specified Ringlock bays.
Install diagonal bracing within the front, side and rear zones.
Complete the 6m front section and 4m rear section.
Install the four LED pallets and five pallet bracket supports at the specified positions.
Coordinate the LED screen installation with the actual cabinet layout and mounting details.
Complete the required project-specific stability, anchoring and structural verification procedures.
This is an explanation of modular composition, not an approved erection sequence or engineering method statement.
16. What Can Be Customized?
The confirmed product is one specific configuration.
Other projects may require changes to:
overall width;
overall depth;
front height;
rear height;
Ringlock bay arrangement;
diagonal bracing layout;
LED pallet quantity;
pallet bracket positions;
LED screen mounting arrangement;
screen elevation.
The important point is that these variables are related.
For example, changing the screen dimensions may change the required front framework geometry.
Changing the rear height or structural depth may change the bracing arrangement and overall modular layout.
These changes should therefore be considered as a complete structural configuration rather than isolated component substitutions.
17. Information Needed for a Similar LED Support Structure
Before preparing a similar structure, the following information is useful:
LED screen width;
LED screen height;
LED cabinet dimensions;
total screen weight;
intended installation elevation;
screen mounting method;
indoor or outdoor use;
available installation depth;
site and ground conditions;
surrounding stage or event structures;
installation location;
existing compatible Ringlock equipment;
reference drawing or elevation.
For this type of structure, a side elevation is particularly helpful because the front and rear heights are different.
The side elevation should clearly show the LED position, front support line, rear support section and overall depth.
18. Engineering and Verification Boundary
The published source confirms:
8m overall width;
4m overall depth;
6m front height;
4m rear height;
79 horizontal pipes;
57 diagonal pipes;
40 vertical standards;
15 adjustable bases;
4 LED pallets;
5 pallet bracket supports;
approximately 1,300kg packing weight;
approximately 3CBM packing volume.
The source does not establish:
maximum LED screen weight;
allowable point loads;
allowable attached load;
wind resistance;
ballast requirement;
anchoring requirement;
foundation requirement;
ground-bearing capacity;
safety factors;
structural certification;
local-code compliance;
engineering approval.
The stepped configuration is a confirmed structural arrangement, not evidence of a particular verified load or wind rating.
Any final LED installation should be reviewed against the actual screen, site conditions and applicable engineering requirements.
The shallower wall and this stepped double-row framework use similar modular component families but have different depth and rear-support arrangements.
20. Original DragonTruss Product and Current Pricing
The original commercial product is:
8x4m Modular Ringlock LED Screen Support Structure 6m Front Height 4m Rear Height
For the current commercial configuration and displayed price, please visit:
The original DragonTruss listing provides the commercial product information and quotation entry.
DragonStructure explains the structural configuration, component relationships and modular arrangement.
DragonTruss provides the original supply information, current pricing and customization quotation.
For a customized LED screen size, rear support arrangement or installation environment, the final quotation may differ from the published product configuration.
FAQ
1. What is the overall size of this LED support structure?
The structure is 8m wide and 4m deep, with a 6m-high front section and a 4m-high rear section.
2. Why are the front and rear sections different heights?
The front section forms the taller LED-support face, while the lower rear section provides additional structural depth and bracing space behind it.
3. Is this a double-row Ringlock structure?
Yes. The confirmed configuration uses a stepped double-row modular arrangement with a taller front section and a lower rear section.
4. How many vertical standards are included?
The BOQ includes 40 LR1 vertical standards, each 2m long.
5. How many horizontal and diagonal members are included?
The configuration includes 79 horizontal pipes, each 2m long, and 57 LR3 diagonal pipes, each 2.44m long.
6. How many adjustable bases are supplied?
The confirmed package contains 15 LR4 adjustable bases, each listed at 0.25m height.
7. What are the LED pallets used for?
The four LED pallets and five pallet bracket supports form part of the lower LED-support arrangement. Their exact operating function and allowable loading should be confirmed for the final installation.
8. Does the product include the LED screen?
No. The published BOQ describes the supporting framework and listed accessories. LED cabinets and associated AV equipment must be quoted separately unless expressly included.
9. Is the LED screen necessarily 8m wide and 6m high?
No. Those dimensions describe the structural framework. The actual LED display dimensions and installation position must be confirmed separately.
10. Is this structure suitable for outdoor concerts?
It is presented as a temporary LED-support configuration for concert and event applications. Outdoor suitability depends on project-specific structural verification, including the actual screen and site conditions.
11. Is ballast included?
The confirmed BOQ does not list ballast. This does not mean ballast or anchoring is unnecessary; any stabilization requirements must be determined for the actual project.
12. Can the rear height or structural depth be changed?
Yes. Different rear heights, depths and bracing arrangements can be considered as customized configurations, subject to confirmation of the complete structural layout.
13. How is this different from the 8x1x6m LED support wall?
The 8×1×6m structure is a relatively shallow support wall. This product has a 4m structural depth and a distinct 4m-high rear section behind the 6m front framework.
14. Is this a complete stage or roof structure?
No. It is a dedicated temporary LED-support framework. The published package does not include a complete performance stage or roof.
Why Rental Companies Put Ground-Supported LED Walls on Stage Risers—and What We Check Before Recommending It
Why Rental Companies Put Ground-Supported LED Walls on Stage Risers—and What We Check Before Recommending ItProject BackgroundThis case analysis started from a public discussion in the video-engineering industry.The question was simple:Why are more ground-supported LED walls being installed on stage
2026-10-30
How We Turned Standard Stage Stairs into a Movable Indoor Venue Entrance System
How We Turned Standard Stage Stairs into a Movable Indoor Venue Entrance SystemProject BackgroundThis project came from an indoor sports and event venue in the Americas.For confidentiality reasons, we do not identify the country or whether the venue is located in North or South America.The venue had
2026-11-13
Why We Use Pivoting Adjustable Stairs Between Different Stage Heights
Why We Use Pivoting Adjustable Stairs Between Different Stage HeightsProject BackgroundA common question in temporary stage systems is:Can one stair unit be used with different stage heights?At first, this sounds like a simple compatibility question.But from a stage manufacturer's point of view, the
2026-11-06
Why a Single Clamped Tube Can Make an LED Wall Difficult to Keep Vertical
Why a Single Clamped Tube Can Make an LED Wall Difficult to Keep VerticalProject BackgroundThis case analysis started from a public video-engineering discussion.The user needed to mount LED panels onto a truss structure.The tested solution used:a single horizontal tube;O-clamps / tube clamps;LED mod
2026-10-17
Why We Split Large Custom Bar Truss Structures After the Overall Design Is Approved
Why We Design Large Custom Bar Truss as One Structure First—and Then Split It for Production and Site AccessProject BackgroundMany of our custom aluminum-truss projects for bars, clubs and entertainment venues begin with the same contradiction.The venue owner or design team wants a large, visually c
Why Rental Companies Put Ground-Supported LED Walls on Stage Risers—and What We Check Before Recommending It
Why Rental Companies Put Ground-Supported LED Walls on Stage Risers—and What We Check Before Recommending ItProject BackgroundThis case analysis started from a public discussion in the video-engineering industry.The question was simple:Why are more ground-supported LED walls being installed on stage
2026-10-30
How We Turned Standard Stage Stairs into a Movable Indoor Venue Entrance System
How We Turned Standard Stage Stairs into a Movable Indoor Venue Entrance SystemProject BackgroundThis project came from an indoor sports and event venue in the Americas.For confidentiality reasons, we do not identify the country or whether the venue is located in North or South America.The venue had
2026-10-30
Why We Use Pivoting Adjustable Stairs Between Different Stage Heights
Why We Use Pivoting Adjustable Stairs Between Different Stage HeightsProject BackgroundA common question in temporary stage systems is:Can one stair unit be used with different stage heights?At first, this sounds like a simple compatibility question.But from a stage manufacturer's point of view, the
2026-11-13
Why a Single Clamped Tube Can Make an LED Wall Difficult to Keep Vertical
Why a Single Clamped Tube Can Make an LED Wall Difficult to Keep VerticalProject BackgroundThis case analysis started from a public video-engineering discussion.The user needed to mount LED panels onto a truss structure.The tested solution used:a single horizontal tube;O-clamps / tube clamps;LED mod
2026-11-06
Why We Split Large Custom Bar Truss Structures After the Overall Design Is Approved
Why We Design Large Custom Bar Truss as One Structure First—and Then Split It for Production and Site AccessProject BackgroundMany of our custom aluminum-truss projects for bars, clubs and entertainment venues begin with the same contradiction.The venue owner or design team wants a large, visually c
DragonStructure is a specialized platform created to explore modular temporary structures, structural applications and system integration for events and other professional temporary-structure projects.